How to Build a Planter Box with Trellis

How to Build a Planter Box with Trellis-Barmes Garden answer. Today. I want to show you how to make this beautiful trellis planter. I wanted to build this planter because we've got a long stretch of wall on our patio that had nothing on it. So it kind of bothers me that I couldn't figure out exactly what I wanted to put there and I've seen pictures of this kind of planter around but couldn't find one that was quite my taste. So I kind of melded, a bunch of different ideas together and came up with this design. So let's start at the beginning. The fun part about these type of projects for me is that you can really make them your own. So the first thing I did was I sat down. I figured out what dimensions I wanted it to be in the end. I'm going to do a four foot wide Box by 7 feet tall and it's going to be about 20 inches deep after I made my Cutlass for this project and knew exactly how much would I was going to need. And we went down to Home Depot to pick it all up and I'm hoping that we don't have to make a second trip. Now, what I'm going to do is take all of our wood and cut it into the appropriate sized pieces, that we need based on the cut list. 

Keyword: trellis planter b&q, how to build a planter with trellis, privacy planter box, vinyl planter box with trellis, planter box with lattice trellis, tall planter boxes for privacy, trellis planter homebase, planter box with trellis screen

First. I cut all of The lumber according to my cut list except for the front and side trim pieces, which I will talk about later. I'd like to try to keep my cuts as organized as possible as I go. Keeping side pieces together from pieces together and so on making assembly quicker and easier. Now that all the lumber is cut, we can start assembling the interior frame. I started with the front and back pieces for the front. Clamp, one of the longboards to your work surface. Align the shorter board to the center and drill to 1/8 inch pilot, holes diagonally. From the shorter board into the longer board, then secure with two and a half inch screws unclamp, flip it around and attach the other longboard. It should look like a giant H. Repeat these steps with the back pieces. Keeping in mind that the back piece will be shorter to accommodate the 4x4 post later on. We'll build the sides. Next using the free shorter pieces. I clamp the long one down to the work surface, align the shorter boards flush to the ends of the long one. I drill pilot holes and fastened with screws the same way we did before it will resemble a giant sea.

Garden Answer

Next, we need to put all the assembled pieces together. It was easiest with the four by fours lying on the ground. I attach the side pieces to the four by fours, then attached the back piece and the front piece.

 I had helped to flip the whole frame up so I could attach the floorboards five on each side of the center, support boards. I drilled to pilot holes on the end of each two-by-four and secured with the two and a half inch screws. We then laid it back down. So we could attach the feet attached. The heavy duty of top plates first and simply screw in the feet.

Garden Answer

While the frame was still lying down. I installed the one by six seater board starting with one of the top side pieces. So I can make sure it was flush with the top of the box. I attached the other top side piece. Then the front piece, I continued in this pattern until I reach the bottom, the bottom boards will hang over the bottom of the frame just slightly which is what you want, get help to lift the planter upright and install the back pieces. Next. I held up the lattice to see if it needed to be cut to fit. It was a little

 So I used a jigsaw to cut it to size. I really wanted the top to be curved. So we laid the lattice on the ground and my helpful husband, Aaron held the flexible piece of trim in an arc on the trellis so I could trace how I wanted it cut. I used the jigsaw again to cut it into a narc. It was a little tricky, attaching the trim to the top of the curve lattice. We tried small nails and screws but ended up using wood glue wherever the lattice met the trim, while I held them tight wiping. Any excess glue. Erin wired each joint. We left the wires on overnight so that the glue had ample time to dry. I left the lattice alone to dry for a bit and installed the finials to the top of the four by four post with wood glue, making sure to wipe any excess glue off.

Garden Answer

Aaron held the lattice up to the back of the post. And I use several small nails to attach it. I read measure the front of the box and cut the board with 45 degree angles on both ends. Line up all the boards, drill pilot holes and attach with two and a half inch screws. Hey guys. It's day two of this building project. As you can see, we have our almost finished product here. We threw in the towel yesterday when we started to lose light. It was a little over a hundred degrees and that was really tough to build in yesterday. So all we need to do today is release the wire that we clamp down this the trim with yesterday. The second to last step. I believe, we're going to stain the whole thing. And then we're going to plant it up and it'll be done. You remember yesterday that we use wood glue to attach this piece of trim to

 Top of the trellis. And then we use little pieces of wire along the length of the trellis to keep it attached until it. So, I'm going to go ahead and cut off all of the wire pieces and hope that the term stays on.

Garden Answer

There are a lot of different finishes that you can apply to this would, but I chose to use a stain. So I'm going to use a decking stain that I had in the garage. You can tell it's a well-loved can of stain. This is a Cabot. It's a water repelling wood stain. So I figured it would be really good to use on an outdoor project like this. So we'll just go ahead and stay in the whole thing.

 We just got it all stained and I'm liking it. I know now that lattice is a total pain to stain. I really like to start with staying because it's easy to kind of modify later. You can go darker if you want to or after living with it for a while, you can decide if you

 I paint it but it's hard to go from paint back to Wood. So stains the way to go in the beginning. For me. We're almost done. We have two more steps to go. First. We have to line the inside of the Box before we can plant. So I've got my staple gun here and then I just had this piece of its kind of like a tarp playing around. You can use landscape fabric, which is probably one of the better choices to use because it allows water to escape quickly, but I'm going to line it with this and then I'll cut a few scores in the bottom. So water can drain.

 

Garden Answer

I'm just going to cut all the excess off here. These are the plants I picked out for the planter. I'm going to grow a sweet Autumn clematis up the lattice. And then I'm going to do three Jade, princess pennisetum. I did three Blackie potato vine and then a few.

 Panache, marshmallow petunias. I think this color combination is really pretty. Let's fill it up with soil and put these in. So it took about three, two cubic foot bags and Miracle-Gro potting soil, fill this container first. I'm going to plant the clematis and I want to do that right in the center so that I can grow up and fill the lattice evenly. Rough up its roots, just a little bit and break that route memories. Go to stand back a little bit and make sure I've got it right in the center. Next. I'm going to plant my grasses.

 And then the potato vines.

 And then I'll put in the petunias.

Garden Answer

So there you have it all done and I'm loving what it's doing for this wallet. Totally softens, the appearance of it. I also think it would work great as a privacy planter. If you don't have a fence between you and the neighbors, you could also use it to hide something unsightly in your garden, like a air conditioning unit or some kind of shed that you don't like the look of you also don't even have to use it for just pretty stuff. You could also use it for practical purposes. You could use the lattice as a support for pull peas or pole beans. And then you can use the planter bed for Things that are shorter so you could grow vegetables as well as pretty things. Thanks for watching.

Garden Answer